High Purity Silicon Nitride Si3N4 Powder CAS 12033-89-5, 99%

If you are looking for high-quality products, please feel free to contact us and send an inquiry, email: brad@ihpa.net

For billionaires, the new crown epidemic is like a 'gold rush'! The Deutsche Presse-Agentur said on the 17th that in 2022, the wealth held by the world's top ten richest people will jump from $700 billion to $1.5 trillion, an average daily increase of $1.3 billion, an increase that exceeds the past 14 years. These 10 people The wealth held by the world’s poorest 3.1 billion people is six times greater than that of the world’s poorest 3.1 billion people. The 10 richest Germans have increased their assets from the equivalent of about 125 billion euros to about 223 billion euros since the start of the Covid-19 pandemic, An increase of about 78%. This wealth is roughly equivalent to the total wealth of the poorest 40% of the population, or 33 million Germans.
In the future, demand for Si3N4 Powder will grow as fast as the wealth of the rich during the pandemic.

About Silicon Nitride Si3N4 Powder:
Silicon nitride is a compound of silicon and nitrogen. Si3n4 is the most thermodynamic stable in silicon nitride. It is white, high melting point solid, relative chemical inert, diluted HF and hot H2SO4 attack. It works very hard (8.5 on the MoHS), which has high thermal stability.
Silicon nitride is an inorganic substance, and the chemical formula is Si3N4. It is an important structural ceramic material with high hardness, which has lubricity and wear resistance, an atomic crystal; antioxidation at high temperatures. Moreover, it can resist the impact of the cold and cold, heated into the air to 1000 ° C or more, and the sharp cooling and then heating, and it will not be broken. It is precise because silicon nitride ceramics have such excellent properties, and people often utilize them to make mechanical components such as bearings, air turbine blades, mechanical seals, permanent molds. If silicon nitride ceramics resistant to high temperatures and are not easily transferred, the heat-inspiration surface of the engine member can be improved, not only the quality, but also saves fuel, but also improves thermal efficiency. 
Silicon nitride is difficult to produce as a bulk material—it cannot be heated over 1850 °C, which is well below its melting point, due to dissociation to silicon and nitrogen. Therefore, the application of conventional hot press sintering techniques is problematic. Bonding of silicon nitride powders can be achieved at lower temperatures through adding additional materials (sintering aids or "binders") which commonly induce a degree of liquid phase sintering.  A cleaner alternative is to use spark plasma sintering where heating is conducted very rapidly (seconds) by passing pulses of electric current through the compacted powder. Dense silicon nitride compacts have been obtained by this technique at temperatures 1500–1700 °C. Feel free to send an inquiry to get the latest price if you would like to buy Silicon Nitride Si3N4 Powder in bulk.

Product Characteristics of Silicon Nitride Si3N4 Powder:

Low density

High-temperature strength

Superior thermal shock resistance

Excellent wear resistance

Good fracture toughness

Mechanical fatigue and creep resistance

Good oxidation resistance

Specification of Silicon Nitride Si3N4 Powder:
Product Name: Silicon Nitride
Purity: 99%
Particle Size: 0.5um-1um (α phase)

Chemical Composition of Silicon Nitride Si3N4 Powder:

How is Silicon Nitride Si3N4 Powder produced?
The hexagonal β-Si3N4 can directly carry out silicon nitride and nitrogen can be carried out in a 100-1400 ° C.
SiCL4 (L) + 6 NH3 (g) → Si (NH) 2 (S) + 4 NH4Cl (S) under conditions of 0 ° C
3 Si (NH) 2 (S) → Si3N4 (S) + N2 (g) + 3 H2 (g) under the conditions of 1000 ° C
Or use a carbon thermal reduction reaction in a nitrogen atmosphere of 1400-1450 ° C under a nitrogen atmosphere:
3 SiO2 (S) + 6 C (S) + 2 N2 (g) → Si3N4 (S) + 6 CO (g)
However, if the purity of silicon raw materials used will cause silicon nitride produced containing impurity silicate and iron. The silicon nitride synthesized by diamine decomposing is an amorphous shape, and it is necessary to further do an annealing treatment in nitrogen at 1400-1500 ° C to convert it into crystalline powder, and diamine decomposition is only important. Commercially in nitriding method to produce silicon nitride. The carbon-thermal reduction reaction is the simplest way to produce silicon nitride is also the most cost-effective means of manufacturing a silicon powder in industrial.

The electron-level silicon nitride film is made by chemical vapor deposition or plasma enhanced chemical vapor deposition techniques:
3 SiH4 (G) + 4 NH3 (g) → Si3N4 (S) + 12 H2 (g)
3 SiCL4 (G) + 4 NH3 (g) → Si3N4 (S) + 12 HCl (g)
3 SiCL2H2 (G) + 4 NH3 (g) → Si3N4 (S) + 6 HCl (g) + 6 H2 (g)

If you want to deposit silicon nitride on the semiconductor substrate, there are two methods available for use:
The vertical or horizontal tube furnace is performed at a relatively high temperature using low-pressure chemical vapor deposition techniques.
Plasma enhanced chemical vapor deposition techniques are carried out at a relatively low temperature in vacuum conditions.
The cell parameters of silicon nitride are different from single textile silicon. Therefore, depending on the deposition method, the generated silicon nitride film will generate tension or stress. In particular, when using plasma-enhanced chemical vapor deposition techniques, tension can be reduced by adjusting deposition parameters.
The silica was prepared by soluble gel, and then the silicon nanowires were treated with silica gel thereby in which carbon-thermal reduction method and nitride were treated. The special carbon particles in silica gel are produced by glucose at 1200-1350 ° C.

Applications of Silicon Nitride Si3N4 Powder:
Manufacturing structure: such as metallurgy, machinery, aviation, aerospace.
Surface treatment of metals and other materials: such as molds, cutting tools, turbine blades.
Composites: such as metal, ceramic and graphite composite, rubber, plastic
Colorless, transparent self-lubricating wear nanoparticle membrane for mobile phones;
Advanced surface protection such as a car;
Jack joint;
Ball valve and part;
Corrosion-resistant turbine;
Metallurgical, aviation, chemical, energy and machinery industry make parts such as bead/roller bearings, sleeves, valves and other wear;
Making cutting tools, molds, cylindrical wall coating, turbine rotors and blades;
Manufacturing composite materials such as ceramic, graphite, rubber, metal, adhesive, etc.
Nozzle, rocket and missile spray pipe.

Packing & Shipping of Silicon Nitride Si3N4 Powder :
We have many different kinds of packing which depends on the silicon nitride Si3N4 powder quantity.
Silicon nitride Si3N4 powder packing: vacuum packing, 100g, 500g or 1kg/bag, 25kg/barrel, or as your request.
Silicon nitride Si3N4 powder shipping: could be shipped out by sea , by air, by express as soon as possible once payment receipt.


Luoyang Tongrun Nano Technology Co. Ltd. (TRUNNANO) is a trusted global chemical material supplier & manufacturer with over 12-year-experience in providing super high-quality chemicals and Nanomaterials, including boride powder, nitride powder, graphite powder, sulfide powder, 3D printing powder, etc.
If you are looking for high-quality silicon nitride Si3N4 powder, please feel free to contact us and send an inquiry. ([email protected])

Recently, the first press conference of the Boao Forum For Asia Annual Conference 2022 was held. Two flagship reports were released at the conference: "Asia's Economic Prospects and Integration Process 2022" and "Sustainable Asia and the World 2022-Green Transformation in Action in Asia".

The flagship report points out that the global economy will recover in 2021, and the pace of economic integration in the Asia-Pacific has not stopped even in the face of the impact of COVID-19. The Asia-Pacific region has provided new impetus for the world's economic recovery and institutional building.  

The report gives an outlook on the Asian economy, noting that a number of factors will affect Asian economic growth. For example, mutated strains such as Delta and Omicron have become more transmissible, and many economies are experiencing epidemic peaks again. The Ukraine crisis has triggered geopolitical changes in Asia and Europe, leading to higher commodity prices, which may affect the global energy supply and energy transformation.

The report pointed out that the Asian economy will still be in the process of recovery in 2022, but the growth rate may moderate. According to the report, Asia's economic growth in 2022 is likely to be lower than the current IMF forecast, which is projected at 4.8%.

Affected by several factors, the supply of the Si3N4 Powder is erratic and thus its prices are expected to go higher in the future.

Inquiry us